Sink - cabinets artificial Stone production line | automatic-automation cultured marble-granite & solid surface artificial stone
Artificial stone production line to produce a variety of sinks and Washcloth sink similar to cultured marble-granite & solid surface, Stone cabinets, counter-tops, artificial Tombstone, under the shower stone, antique partition and ... in the form of Semi-automatic and automation
Elevator Carries Solids : Automatic transport of aggregates and solids , Calcium carbonate and ... (and adhesive compounds) , with a capacity of 300 kg per minute and the entry and exit valve, with a height of 730 cm, with an electrical motor 7.5 HP, three-phase, with special custom envelopes and Taiwan chains and ... with an output valve guided to a separate mixer
Two-piece vibrating hopper, single part : two-piece vibrating hopper has a custom-made vibrator motor for aggregate and alternative materials, also for the storage of solid materials in a mesh tank with a 500 kg three-phase electrical motor
Combined mixer designed by PAN and vertical, Mixer machine, for artificial marble-granite (cultured marble-granite, onyx, pebble design, solid surface, stone adhesive and … : motor 7.5 HP three-phase and custom gearbox with mixing method from above, with a rotation output of 46 rpm, spiral linear blades, the thickness of the floor sheet is 8 mm and the wall thickness is 6 mm,has a manual exit part - the diameter of the mixer is 100 cm and the body height is 65 cm with a volume of 500 liters with a capacity of 350 to 400 kg due to the formulation and meshing of minerals, and resin materials similar to pebble design up to 450 kg, with winch 400.800 to move the mixer up and down with the structure of the gearbox mounted on the mixer, the total height of the mixer is about 300 cm.
Central control panel: power system and central control panel machines and equipment, with the motherboard to control and command all machines with their respective monitors, with the ability to report previous production - equipped with a 7-inch Touchscreen - has an inverter in the molding system, Schneider Electric Germany, France TELECOM, and DELTA, with programming for the production line
Vibration machine with width 55 in length at 400 centimeters: vibrating table for marble artificial granite with a width of 55 cm and a length of 400 cm, with a 300 kg vibrating electro-motor with ability Configurable with 8 special springs with a height of about 12 cm, with iron 5*3 centimeters with bottom holder and screw to the ground, for production of cabinets with a length of 400 cm and a width of 70 centimeters – has a roller transfer on the surface of the vibrating table for ease of movement of molds and materials
Roller table under the gate: work table with dimensions of 60 cm along 400 cm direction under the gate for the molding of materials with iron 5*3and rotational roller
Automatic weighing Mixer System:has automatic command for 3 materials and several defining formula with 4 bending load cell under mixer
Custom injection molding system Screw:Screw transfer material with a pneumatic butterfly valve, electrical valve accessories and water trap & pressure control, crust screw 4 mm and bung 2 mm, middle shaft tube of 2.5 inches, the thickness of the sheet is 6 mm, with a 4 mm diameter hopper with a capacity of 600 kg,With a length of 370 cm with a 5/5 HP motor and HOLLOW SHAFT gearbox with control of the round
In the production line of the second type semi-automatic, some items of equipment are replaced by the following items and specifications:
Two-piece vibrating hopper, has engine and Inverter : two-piece vibrating hopper has a custom vibrating motor to save aggregates and alternative materials, also for storing solids in a mesh tank with a three-phase electro-motor 500 KG | Hopper special changes: two fragmentation of the hopper section with 4 MM sheet, has two outputs, with 4 horse engines and direct cobble gearbox 100 output round with inverter
Combined mixer designed by PAN and vertical, Mixer machine, for artificial marble-granite (cultured marble-granite, onyx, pebble design, solid surface, stone adhesive and … : motor 10 HP three-phase and custom gearbox with mixing method from above, with a rotation output of 46 rpm, spiral linear blades, the thickness of the floor sheet is 10 mm and the wall thickness is 8 mm, has a manual exit part - the diameter of the mixer is 120 cm and the body height is 65 cm with a volume of 700 liters with a capacity of 500 to 600 KG due to the formulation and meshing of minerals, and resin materials similar to pebble design up to 600 kg, with winch 400.800 to move the mixer up and down with the structure of the gearbox mounted on the mixer, the total height of the mixer is about 300 cm.
Central control panel: power system and central control panel machines and equipment, with the motherboard to control and command all machines with their respective monitors, with the ability to report previous production - equipped with a 7-inch Touchscreen - has an inverter in the molding system, Schneider Electric Germany, France TELECOM, and DELTA, with programming for the production line
Vibration machine with width 80 in length at 400 centimeters: vibrating table for marble artificial granite with a width of 80 cm and a length of 400 cm, with a 300 kg vibrating motor with ability Configurable with 8 special springs with a height of about 12 cm, with iron 6*6 centimeters with bottom holder and screw to the ground, for production of cabinets with a length of 400 cm and a width of 90 centimeters – has a roller transfer on the surface of the vibrating table for ease of movement of molds and materials
Roller table under the gate: work table with dimensions of 80 cm along 400 cm direction under the gate for the molding of materials with iron 6*6 and rotational roller
Custom injection molding system Screw:Screw transfer material with a pneumatic butterfly valve, electrical valve accessories and water trap & pressure control, crust screw 4 mm and bung 2 mm, middle shaft tube of 2.5 inches, the thickness of the sheet is 6 mm, with a 4 mm diameter hopper with a capacity of 600 kg,With a length of 370 cm with a 5/5 HP motor and HOLLOW SHAFT gearbox with control of the round